Call: 0800 AAA WALL (222 9255)

  • Home
  • Warmafloor Technical Information


floorinsulation1 Floor Insulation Technical Info | Warmafloor - AAA Insulation

Warmafloor is a Polyester fibre blanket manufactured specifically for placing between floor joists, against the underside of the floor. This blanket has superior strength in both directions and tighter surfaces than other typical polyester ceiling, wall or floor blankets or batting.

The rolls are uniquely sized to facilitate handling in confined sub-floor spaces and can be torn readily to suit joist length.


Thermal Effectiveness
Uninsulated floors have a thermal resistance of R0.6, which can be improved to R1.6 or R1.8 with Warmafloor Blanket System correctly fixed against the floor, between the floor joists in most buildings with a continuous sub-floor perimeter wall. It also reduces draughts through gaps between uncovered timber strip floors.

Compliance with NZ Building Code (NZBC) clause H1.3.1 (a) and H1.3.2 with Warmafloor is achieved via H1/AS1, clauses 2.1, 2.2 and 2.3. Alternatively, should installers complete a design on an individual building in accordance with NZS4218 calculation method, other R values specified in Table 1 will comply.


Warmafloor blanket will satisfy the requirements of NZBC clause 2.3.1(a) & B2/AS1 Table 1 of 50 years durability in dry, suspended timber floors.

Warmafloor blanket does not promote corrosion on metal building components.

Moisture Effects
Warmafloor blanket is unaffected by humidity or water. It can contribute to NZBC section E3.3.1 and complies with E3/AS1, section 1.1. If wetted, thermal resistance will be completely restored, when dried.


This designated “Design”, “Construction” or “Construction without Building Consent” statement covers the use of Warmafloor to meet or exceed the NZ Building Code sections B2, E3, F2, H1 requirements, when used in buildings at any geographical location in accordance with this document.

For floors, BCA’s need only inspect that material thickness is in accordance with the thermal effectiveness design specified.


Fire Properties
Polyester is classified as a combustible material but contains a flame retardant additive.

Health Effects
Warmafloor complies with NZBC section F2.3.1, as non-hazardous material. The product does not represent a health risk to installers or occupiers of insulated buildings.

Warmafloor is not dusty or a skin irritant, however, face masks and overalls should be worn when working with all insulation materials.


A hammer stapler, 8-12mm staples, protective overalls, face mask & goggles are required to install floor insulation. Avoid any bare wires and do not staple within 50mm of any wire.

Start at the end of one joist, push Warmafloor Blanket up between the joists, until it touches the floor. Adjust so the side laps are equal, staple through the lap fold into one joist, pull tight and staple the other lap fold to the adjacent joists. Continue stapling at about 1m centres (or 0.5m if animals can reach the material) and at joist laps, ensuring there are no edge gaps.

Feed the blanket over the next bearer and butt joint the next blanket. If the roll is too long, hand tear to length across the roll. Wherever pipe or wires protrude through the floor tear the blanket from one side and wrap around the pipe. Width trimming should not be necessary but can be cut with shears or scissors.

    • We Have Professional NZ Home Insulation Installers from Gisborne to Wellington

      • For a free quote

        Email AAA Insulation Today

        Contact Us

        Mon – Fri: 9AM – 5PM
        Call: 0800 222 9255
        A/H: 021 375 359

      • Our Locations

        Gisborne and the East Cape
        Hawke's Bay
        TaupoIAONZS Floor Insulation Technical Info | Warmafloor - AAA Insulation

  • Contact us for NZ House & Home Insulation, Wall Insulation, Roof Insulation & Floor Insulation
    Website-main1 Floor Insulation Technical Info | Warmafloor - AAA Insulation